Plumbing 101: A Guide to Bathtub Installation

Click Here

Just how do you actually feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


Installing A Bathtub
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough project. If the old tub is readily obtainable, the project can move easily; if you have to open up a wall surface to remove the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to leave the old tub and set in the new one. See to it you have actually qualified on your own for the task and fit trying it. Instead of employing a contractor to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you install a brand-new tub in your restroom if you have actually currently bought a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices as well as product checklist must make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite troublesome due to the limited access that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
    Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipes.
    If you require to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be linked to the tap ends first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, position the bathtub in the needed placement. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
    The following goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the tub up until the level reads degree.
    To set up taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
    Turn on the water supply and also examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and also the regular outlet for leaks.
    Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub should wait up until the bath tub has actually been utilized at the very least once as this will settle it right into its last setting.

    Preparing for the Installation


    Firstly, the supporting framework supplied with the bath ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
    Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final placement.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to complications with dampness and possible leakages to the ceiling listed below.
    You can pick from a variety of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly early if you do not consider this movement before sealing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water-proof adhesive and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    I'm just very focused on How to Install a Bathtub and I'm hoping you liked the entire piece. Those who liked our page plz don't forget to share it. I am grateful for your time. Visit us again soon.


    Dial, we deliver!

    Leave a Reply

    Your email address will not be published. Required fields are marked *